Item Tag: Electronics

5W Solar Panel Charger for Ring Video Doorbell 4/3/2 Solar Charger w/Power Cable

5W Solar Panel Charger for Ring Video Doorbell 4/3/2 Solar Charger w/Power Cable About this item Compatible with Ring Battery Doorbell：The 5w solar panel for Ring Video Doorbell 2, Video Doorbell 3/3+, Video Doorbell 4. This solar panel is not compatible with video doorbells without batteries. If your video doorbell does not have a rechargeable battery, please do not purchase this solar panel. Continuous Solar for Your Doorbell: The solar panel continuously absorbs sunlight to recharge your doorbell battery, get rid of the trouble to remove the doorbell battery frequently to charge it. The panel does not have an internal battery, The panel will charge that battery using the sun. IP 65 Waterproof：This solar panel with ip65 waterproof, monocrystalline silicon material is very durable, and the operating temperature range is -4 °F to 122 °F. It can resist rain, snow, suitable for outdoor use. Easy to Install: This solar panel with 360 degree adjustable bracket and 10ft charging cable, you can install the solar panel in the most suitable position facing the sun. High Efficiency Solar Panel: This solar panel is designed with high efficiency monocrystalline silicon material, the charging efficiency is higher than other solar panels, it can quickly charge your battery doorbell with high cost performance. Important Tips： 1.The 5w solar panel is Compatible with Ring Video Doorbell 2, Video Doorbell 3/3+, Video Doorbell 4. 2.The panel does not have an internal battery, The panel will charge that battery using the sun. Please install the solar panel in sufficient sunlight. 3.This solar panel is not compatible with video doorbell without battery, please do not purchase this solar panel if your video doorbell does not have rechargeable battery. 4.Recommends at least 3-4 hours of direct sunlight, depending on your usage. You will want to make sure there are no obstructions that could be casting a shadow on your Ring Solar Panel such as an extended roof, trees, bushes, etc. 5.Please confirm your doorbell model before purchasing. Technical Details Product Dimensions: Solar Panel: 6.7 in x 4.7 in x 0.5 in (17cm x 11cm x 1.3cm) / Cable: 10 feet (3m) in length. Connection: Fork Connector. Solar Panel Power Rating: 5W, 5VDC. Material：Monocrystalline Silicon Maximum Voltage：‎5 Volts Maximum Power：5 Watts What’s in the package 1 x 4W solar panel for ring doorbell 1 x Screws bag 1 x basePaymentDelivery detailsTerms of salesAbout usContact usPaymentPayPal only.Payment should be completed within 4 days after auction closed, or unpaid dispute will be filed for an closing auction. An unpaid case will be filled after 4 days.Delivery details1.We only ship this item to United State!2.We ship to your eBay address. Each package will be shipped to USA by USPS or Fedex with tracking number.3.Please check your shipping address carefully before checkout, it can’t be changed if order completed.4.Ship within 1-2 business day once payment completed. Orders placed on weekend will be shipped within 3 days.5.ONLY ship to PayPal shipping address. Please make sure your PayPal shipping address is correct before finalizing order and submitting payment. We only ship to the shipping address submitted with the payment. We will not be responsible for item loss due to wrong or unknown address.Terms of sales1. We offer a 30 Day return policy on all items purchased on eBay.2.Simply contact us through eBay messages within 14 Days after receipt of item to process a return.3. Please contact with us before you ship the goods back.About us1. We maintain high standards of excellence FIVE STAR and strive for 100% customer satisfaction!2. Positive Feedback is very important to us. We hope that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.3. We promise to offer the lowest price and high quality produce.4. Our working time: From Monday to Friday(8:30 am to 18:00pm), we do not work on holidays in China,hope you can understand and know that , thank you.5. Please always talk to us via ebay Message.6. We appreciate your business and look forward to growing our eBay sales with satisfied customers.Contact usDear buyers,Welcome to our store!Your satisfaction is our top goal,we appreciate your business.1. If you have any questions, please feel free to contact with us by ebay Message during our business hours ( 8:30a.m. to 6:00 p.m.), or email us through eBay, we will try our best to help you to resolve it.2. If you are satisfied with our service, please rate the details of the transaction (Detailed Seller Ratings) on eBay and We will do the same for you.3. If you are not satisfied with the product or service ,please contact us before leave negative or natural feedback, we will try our best to solve the issue to your satisfaction, thanks.Thanks for your patronizing!

Electronic Single Axis Solar Tracker Controller W/ Wind Sensor DIY Solar Kits DO

Electronic Single Axis Solar Tracker Controller W/ Wind Sensor DIY Solar Kits Electronic Single Axis Solar Tracker Controller W/ Wind Sensor DIY Solar Kits Package Included: * 1PCS WST03-3 Electronic LCD Controller Box. * 1PCS Light Sensor with 3 Meters Wire. * 1PCS IR Remote Control (No Battery Included). * 1PCS Wind Speed Sensor (Anemometer) with 3 Meters Wire. * 1PCS English User’s Manual. Single Axis Solar Tracker Controller: Here for sale is WST03-3 Single Axis Solar Tracker Controller, items include the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control, we will provide English Manual together with the items. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun.Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode.Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Specification:Product NameWST03-3 Solar Tracker ControllerBrandSZMWKJCondition100% NewController Box Dimension145x90x40mm (5.71″x3.54″x1.57″)Input VoltageDC 12V/24V (DC 9V~35V)Max Load Current15AOperating Temperature-20℃ to +60℃Tracking Accuracy≤1° Controller Box: Controller Features:1. High tracking accuracy, average tracking accuracy ≤ 1° (Actual accuracy is related to the platform’s moving speed);2. The light sensor has a wide range of detection angle and high accuracy. It’s inside the waterproof case, waterproof, dustproof and anti-aging;3. With LCD display which can show multiple working modes and parameters;4. Many of the parameters can be set (Tracking accuracy, threshold value of light-sensor, threshold value of wind speed sensor, interval time of cyclical tracking, etc…);5. With strong wind protection mode (Wind speed sensor is required);6. Can set the platform to stay at any position at night (or cloudy day);7. Can add extra limit switches;8. Can be operated by IR remote control or the buttons on the controller box;9. Reverse battery protection, overcurrent protection; standby current ≤15mA. Controller Attention Matters:1.Input Power Supply: DC 12V/24V (DC 9V~35V); Output Voltage=Input Voltage; Output Current: ≤15A.2.The controller needs stable power supply, it can be battery or switching power supply, solar panels cannot be directly connected as power supply, unstable voltage may damage the controller. The maximum current of the power supply must be greater than 1.5 times of the total load current of the platform, because the starting current for DC motor is relatively large.3.This controller can directly drive DC brush motor, the rated voltage of the motor should be the same as the power voltage of the controller. If use other types motor, this controller cannot directly drive, in this case additional control circuit need to be added.4. If the total load current of the platform is greater than 15A, a relay module is needed to increase the load capacity of the controller.5.The controller is preferably fixedly installed and will not move together with the platform. The controller is not waterproof and should prevent water from entering. Light Sensor and IR Remote: Light Sensor Attention Matters:1. The light sensor should be fixed on the platform and can move together with the platform, it cannot be blocked by anything.2. The base of the light sensor must be parallel to the solar panel or on the same plane.3. The “East” direction marked on the light sensor must be consistent with the local geographic direction.4. The length of the connecting wire for the light sensor must be greater than the platform’s movable range. (Factory default length is 3 meters, it can be increased to 30 meters at most) IR Remote Attention Matters:1. The remote control requires 2 pieces AAA batteries (factory defaults no batteries inside).2. The remote control belongs to infrared remote control, it must be aligned with the controller when using, the remote control range is ≤ 6 meters.3. The buttons on the remote control have the same function as the buttons on the controller box. Wind Speed Sensor (Anemometer): This wind speed sensor is composed of a shell, three wind cups and a circuit module. The whole sensor has a high strength, weather resistance, corrosion resistance and water resistance, will be to ensure the long-term use of the instrument, and the accuracy of the wind speed collection. It is very suitable for outside measurement. Specifications: Brand: SZMWKJModel: MW-FS03Material: Polycarbonate MaterialColor: BlackAccuracy: ± 1m/sStart-up Wind Speed: 0.2-0.4 m/sOutput Type: Voltage OutputMeasurement Range: 0-32.4m/sOutput Signal: 0-5VWind Speed: (Output voltage/5)*32.4m/sCable Length: 3 Meters The solar tracker controller can work normally without the wind speed sensor, but if you want to use the Strong Wind Protection function, you need to use wind speed sensor, the output signal of the wind speed sensor should be voltage type, the signal output range should be 0-5V, the power voltage of the wind speed sensor should be the same as the power voltage of the controller. Wiring of the Wind Speed Sensor: Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * Goods in stock in USA, buyer can get the parcel around 3-5 business days. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer.

LCD Single Axis Solar Tracker Controller 12V 24V Electronic Tracking Controller

LCD Single Axis Solar Tracker Controller 12V 24V Electronic Tracking Controller Click Here to But It Now Click Here to But It Now Click Here to But It Now LCD Single Axis Solar Tracker Controller 12V 24V Electronic Tracking Controller This is WST03-3 Single Axis Solar Tracker Controller, The whole unit contains the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun. Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode. Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Package Included:* 1PCS Single Axis LCD Controller Box;* 1PCS Light Sensor with 3 Meters Wire; * 1PCS IR Remote Control (No Battery Included);* 1PCS English User’s Manual. Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual. About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * We ship via Express Delivery from China which usually takes about 5-7 Business Days to Worldwide. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer.

Single Axis Solar Tracker Controller W/ Anemometer DIY Solar Panel Auto Tracking

Single Axis Solar Tracker Controller W/ Anemometer DIY Solar Panel Auto Tracking Click Here to But It Now Click Here to But It Now Click Here to But It Now Single Axis Solar Tracker Controller W/ Anemometer DIY Solar Panel Auto Tracking About the Solar Tracker Controller: This is WST03-3 Single Axis Solar Tracker Controller, The whole unit contains the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun. Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode. Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. About the Wind Speed Sensor (Anemometer) : This wind speed sensor is composed of a shell, three wind cups and a circuit module. The whole sensor has a high strength, weather resistance, corrosion resistance and water resistance, will be to ensure the long-term use of the instrument, and the accuracy of the wind speed collection. It is very suitable for outside measurement. Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual. About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * Goods are in stock in USA Warehouses, buyer can get the parcel around 3-5 business days. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer. On Oct 18, 2023 at 20:15:41 PDT, seller added the following information:

Solar Panel Auto Tracking Single Axis Electronic LCD Solar Tracker Controller EL

Solar Panel Auto Tracking Single Axis Electronic LCD Solar Tracker Controller Solar Panel Auto Tracking Single Axis Electronic LCD Solar Tracker Controller Package Included: * 1PCS WST03-3 Electronic LCD Controller Box. * 1PCS Light Sensor with 3 Meters Wire. * 1PCS IR Remote Control (No Battery Included). * 1PCS Wind Speed Sensor (Anemometer) with 3 Meters Wire. * 1PCS English User’s Manual. Single Axis Solar Tracker Controller: Here for sale is WST03-3 Single Axis Solar Tracker Controller, items include the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control, we will provide English Manual together with the items. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun.Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode.Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Specification:Product NameWST03-3 Solar Tracker ControllerBrandSZMWKJCondition100% NewController Box Dimension145x90x40mm (5.71″x3.54″x1.57″)Input VoltageDC 12V/24V (DC 9V~35V)Max Load Current15AOperating Temperature-20℃ to +60℃Tracking Accuracy≤1° Controller Box: Controller Features:1. High tracking accuracy, average tracking accuracy ≤ 1° (Actual accuracy is related to the platform’s moving speed);2. The light sensor has a wide range of detection angle and high accuracy. It’s inside the waterproof case, waterproof, dustproof and anti-aging;3. With LCD display which can show multiple working modes and parameters;4. Many of the parameters can be set (Tracking accuracy, threshold value of light-sensor, threshold value of wind speed sensor, interval time of cyclical tracking, etc…);5. With strong wind protection mode (Wind speed sensor is required);6. Can set the platform to stay at any position at night (or cloudy day);7. Can add extra limit switches;8. Can be operated by IR remote control or the buttons on the controller box;9. Reverse battery protection, overcurrent protection; standby current ≤15mA. Controller Attention Matters:1.Input Power Supply: DC 12V/24V (DC 9V~35V); Output Voltage=Input Voltage; Output Current: ≤15A.2.The controller needs stable power supply, it can be battery or switching power supply, solar panels cannot be directly connected as power supply, unstable voltage may damage the controller. The maximum current of the power supply must be greater than 1.5 times of the total load current of the platform, because the starting current for DC motor is relatively large.3.This controller can directly drive DC brush motor, the rated voltage of the motor should be the same as the power voltage of the controller. If use other types motor, this controller cannot directly drive, in this case additional control circuit need to be added.4. If the total load current of the platform is greater than 15A, a relay module is needed to increase the load capacity of the controller.5.The controller is preferably fixedly installed and will not move together with the platform. The controller is not waterproof and should prevent water from entering. Light Sensor and IR Remote: Light Sensor Attention Matters:1. The light sensor should be fixed on the platform and can move together with the platform, it cannot be blocked by anything.2. The base of the light sensor must be parallel to the solar panel or on the same plane.3. The “East” direction marked on the light sensor must be consistent with the local geographic direction.4. The length of the connecting wire for the light sensor must be greater than the platform’s movable range. (Factory default length is 3 meters, it can be increased to 30 meters at most) IR Remote Attention Matters:1. The remote control requires 2 pieces AAA batteries (factory defaults no batteries inside).2. The remote control belongs to infrared remote control, it must be aligned with the controller when using, the remote control range is ≤ 6 meters.3. The buttons on the remote control have the same function as the buttons on the controller box. Wind Speed Sensor (Anemometer): This wind speed sensor is composed of a shell, three wind cups and a circuit module. The whole sensor has a high strength, weather resistance, corrosion resistance and water resistance, will be to ensure the long-term use of the instrument, and the accuracy of the wind speed collection. It is very suitable for outside measurement. Specifications: Brand: SZMWKJModel: MW-FS03Material: Polycarbonate MaterialColor: BlackAccuracy: ± 1m/sStart-up Wind Speed: 0.2-0.4 m/sOutput Type: Voltage OutputMeasurement Range: 0-32.4m/sOutput Signal: 0-5VWind Speed: (Output voltage/5)*32.4m/sCable Length: 3 Meters The solar tracker controller can work normally without the wind speed sensor, but if you want to use the Strong Wind Protection function, you need to use wind speed sensor, the output signal of the wind speed sensor should be voltage type, the signal output range should be 0-5V, the power voltage of the wind speed sensor should be the same as the power voltage of the controller. Wiring of the Wind Speed Sensor: Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * We provide tracking number freely for all buyers. * We ship via Standard Delivery from China which usually takes 8-12 working days to United States. * For other countries, we normally ship by China Post/Singapore Post which takes about 25-40 business days. Please make sure you accept the shipping time before you make purchase. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer.

Solar Panel Auto Tracking LCD Dual Axis Solar Tracker Controller With Anemometer

Solar Panel Auto Tracking LCD Dual Axis Solar Tracker Controller With Anemometer Click Here to But It Now Click Here to But It Now Click Here to But It Now Solar Panel Auto Tracking LCD Dual Axis Solar Tracker Controller With Anemometer About the Solar Tracker Controller: This is WST03-2 Dual Axis Solar Tracker Controller, items include the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control, we will provide English Manual together with the controller. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun. Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode. Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. About the Wind Speed Sensor (Anemometer) : This wind speed sensor is composed of a shell, three wind cups and a circuit module. The whole sensor has a high strength, weather resistance, corrosion resistance and water resistance, will be to ensure the long-term use of the instrument, and the accuracy of the wind speed collection. It is very suitable for outside measurement. Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual. About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * We ship via Express Delivery from China which usually takes about 5-7 Business Days to Worldwide. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer.

Single Axis Solar Panel Tracking Sunlight Tracker Controller DIY PV Solar System

Single Axis Solar Panel Tracking Sunlight Tracker Controller DIY PV Solar System Click Here to But It Now Click Here to But It Now Click Here to But It Now Single Axis Solar Panel Tracking Sunlight Tracker Controller DIY PV Solar System This is WST03-3 Single Axis Solar Tracker Controller, The whole unit contains the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun. Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode. Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Package Included:* 1PCS Single Axis LCD Controller Box;* 1PCS Light Sensor with 3 Meters Wire; * 1PCS IR Remote Control (No Battery Included);* 1PCS English User’s Manual. Application: Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual. About Shipping: * This item will be shipped out within 1-3 Business Days after confirmed payment received. * Goods are in stock in USA Warehouses, buyer can get the parcel around 3-5 business days. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer. On Oct 18, 2023 at 20:15:41 PDT, seller added the following information:

Dual Axis Solar Tracker Controller/Single Axis Automatic Solar Panel Tracking IG

Dual Axis Solar Tracker Controller/Single Axis Automatic Solar Panel Tracking Dual Axis Solar Tracker Controller/Single Axis Automatic Solar Panel Tracking Package Included Optional A: 1PCS WST03-3 Single Axis Solar Tracker Controller（LCD Controller Box+Light Sensor+IR Remote). Optional B: 1PCS WST03-2 Dual Axis Solar Tracker Controller（LCD Controller Box+Light Sensor+IR Remote). Notes: Pls check each mode carefully and choose the right mode as you need! Single Axis Solar Tracker Controller Here for sale is WST03-3 Single Axis Solar Tracker Controller, items include the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control, we will provide English Manual together with the items. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun.Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode.Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Specification:Product NameWST03-3 Solar Tracker ControllerBrandSZMWKJCondition100% NewController Box Dimension145x90x40mm (5.71″x3.54″x1.57″)Input VoltageDC 12V/24V (DC 9V~35V)Max Load Current15AOperating Temperature-20℃ to +60℃Tracking Accuracy≤1° Controller Box: Controller Features:1. High tracking accuracy, average tracking accuracy ≤ 1° (Actual accuracy is related to the platform’s moving speed);2. The light sensor has a wide range of detection angle and high accuracy. It’s inside the waterproof case, waterproof, dustproof and anti-aging;3. With LCD display which can show multiple working modes and parameters;4. Many of the parameters can be set (Tracking accuracy, threshold value of light-sensor, threshold value of wind speed sensor, interval time of cyclical tracking, etc…);5. With strong wind protection mode (Wind speed sensor is required);6. Can set the platform to stay at any position at night (or cloudy day);7. Can add extra limit switches;8. Can be operated by IR remote control or the buttons on the controller box;9. Reverse battery protection, overcurrent protection; standby current ≤15mA. Controller Attention Matters:1.Input Power Supply: DC 12V/24V (DC 9V~35V); Output Voltage=Input Voltage; Output Current: ≤15A.2.The controller needs stable power supply, it can be battery or switching power supply, solar panels cannot be directly connected as power supply, unstable voltage may damage the controller. The maximum current of the power supply must be greater than 1.5 times of the total load current of the platform, because the starting current for DC motor is relatively large.3.This controller can directly drive DC brush motor, the rated voltage of the motor should be the same as the power voltage of the controller. If use other types motor, this controller cannot directly drive, in this case additional control circuit need to be added.4. If the total load current of the platform is greater than 15A, a relay module is needed to increase the load capacity of the controller.5.The controller is preferably fixedly installed and will not move together with the platform. The controller is not waterproof and should prevent water from entering. Light Sensor and IR Remote: Light Sensor Attention Matters:1. The light sensor should be fixed on the platform and can move together with the platform, it cannot be blocked by anything.2. The base of the light sensor must be parallel to the solar panel or on the same plane.3. The “East” direction marked on the light sensor must be consistent with the local geographic direction.4. The length of the connecting wire for the light sensor must be greater than the platform’s movable range. (Factory default length is 3 meters, it can be increased to 30 meters at most) IR Remote Attention Matters:1. The remote control requires 2 pieces AAA batteries (factory defaults no batteries inside).2. The remote control belongs to infrared remote control, it must be aligned with the controller when using, the remote control range is ≤ 6 meters.3. The buttons on the remote control have the same function as the buttons on the controller box. Dual Axis Solar Tracker Controller Here for sale is WST03-2 Dual Axis Solar Tracker Controller, The whole unit contains the Controller Box, Light Sensor With 3 Meters Wire and IR (infrared) Remote control. The controller analyzes the signal from the light sensor, then control the motor of the corresponding direction to execute positive rotation, reverse rotation and stop, and make the platform to be aligned with the sun.Three Modes will appear during the controller’s auto working, the controller will automatically switch the three modes according to different conditions. The three Modes are: Sunny Day Auto Tracking Mode, Night (Cloudy Day) Mode, Strong Wind Protection Mode.Users can set the parameters and working modes by the LCD screen for actual needs. There is an IR Remote for manual control, it can be used for testing when you assemble/use the controller the first time. Extra Limit Switch and Wind Speed Sensor (Anemometer) can be matched with the controller for actual needs. We provide more instruction and detailed settings in the English User’s Manual. Specification:Product NameWST03-2 Solar Tracker ControllerBrandSZMWKJCondition100% NewController Box Dimension145x90x40mm (5.71″x3.54″x1.57″)Input VoltageDC 12V/24V (DC 9V~35V)Max Load Current15AOperating Temperature-20℃ to +60℃Tracking Accuracy≤1° Controller Box: Controller Features:1. High tracking accuracy, average tracking accuracy ≤ 1° (Actual accuracy is related to the platform’s moving speed);2. The light sensor has a wide range of detection angle and high accuracy. It’s inside the waterproof case, waterproof, dustproof and anti-aging;3. With LCD display which can show multiple working modes and parameters;4. Many of the parameters can be set (Tracking accuracy, threshold value of light-sensor, threshold value of wind speed sensor, interval time of cyclical tracking, etc…);5. With strong wind protection mode (Wind speed sensor is required);6. Can set the platform to stay at any position at night (or cloudy day);7. Can add extra limit switches;8. Can be operated by IR remote control or the buttons on the controller box;9. Reverse battery protection, overcurrent protection; standby current ≤15mA. Controller Attention Matters:1.Input Power Supply: DC 12V/24V (DC 9V~35V) Output Voltage=Input Voltage Output Current: E/W≤7.5A, S/N≤7.5A, total current ≤15A2.The controller needs stable power supply, it can be battery or switching power supply, solar panels cannot be directly connected as power supply, unstable voltage may damage the controller. The maximum current of the power supply must be greater than 1.5 times of the total load current of the platform, because the starting current for DC motor is relatively large.3.This controller can directly drive DC brush motor, the rated voltage of the motor should be the same as the power voltage of the controller. If use other types motor, this controller cannot directly drive, in this case additional control circuit is needed.4.If the motor current in a single direction is greater than 7.5A, a relay module is needed to increase the load capacity of the controller.5.The controller is preferably fixedly installed and will not move together with the platform. The controller box is not waterproof and should prevent water from entering. Light Sensor and IR Remote: Light Sensor Attention Matters:1. The light sensor should be fixed on the platform and can move together with the platform, it cannot be blocked by anything.2. The base of the light sensor must be parallel to the solar panel or on the same plane.3. The “East” direction marked on the light sensor must be consistent with the local geographic direction.4. The length of the connecting wire for the light sensor must be greater than the platform’s movable range. (Factory default length is 3 meters, it can be increased to 30 meters at most) IR Remote Attention Matters:1. The remote control requires 2 pieces AAA batteries (factory defaults no batteries inside).2. The remote control belongs to infrared remote control, it must be aligned with the controller when using, the remote control range is ≤ 6 meters.3. The buttons on the remote control have the same function as the buttons on the controller box. Application Solar tracking system: Solar photovoltaic System, solar thermal system, light guide and lighting, etc. Want more information? Additional information and detailed instructions can be found in the User’s Manual About Shipping * This item will be shipped out within 1-3 Business Days after confirmed payment received. * Goods in stock in USA, buyer can get the parcel around 3-5 business days. * We provide tracking number freely for all buyers. * Please confirm your shipping address is correct. Buyers are responsible for undeliverable order due address mismatch. We reserve the right to charge shipping fee to reship undeliverable items. * Any potential customs tax fee applied to the parcel should be covered by the buyer. On Oct 18, 2023 at 04:31:03 PDT, seller added the following information: