Item Tag: Amorphous (Thin-Film)

BATTERY TENDER 022-0202-COS Battery Charger 60HW86

Battery Charger, Charger Input Voltage 120V AC, Charger Output Voltage 6V to 12V, Application Automotive, Features Charger will Fully Recharge and then Maintain a Battery At Its Proper Storage Voltage Without the Damaging Effects Caused by Trickle Chargers, Standards BC, CSA, FCC, RoHS, UL, Automatic/Manual Automatic.

12 volt Solar Battery Maintainer Car Panel Charger 2-watt

Keep your vehicle’s battery topped off with this solar battery maintainer. Designed to compensate for small, steady battery drains from the vehicle’s clock or alarm system, this solar charger mounts easily to the windshield or dash and conveniently plugs into your car’s 12 volt cigarette lighter port. With an amorphous crystal solar array, this solar charger provides superior performance in bright sun and in partial shade. Plugs into 12 volt cigarette lighter Panel mounts easily to windshield or dash – includes suction feet for mounting Includes cigarette lighter adapter and battery terminal clamps

Uni-Solar PVL-116 Flexible Solar Panel – 116 watts

Uni-Solar PVL-116 Flexible Solar Panel – 116 watts. New panels, purchased for a project that wasn’t ever built. 116 Watt Brand New PowerBond 30 Volt Amorphous Solar Panels with Top Facing MC3 Connector Cables. These are new panels from old stock and are still in 2 new cartons of 20 panels each. They are in brand new condition. Uni-solar PVL-116 flexible panels are no longer made and are getting harder to obtain by the day. These panels are 116-watt flexible panels that are lightweight and have a peel and stick pressure-sensitive adhesive backing that needs no additional mounting hardware. Designed specifically for flat metal (standing seam), and rubber (EPDM) roofs, but they also work great for RV, boat, and truck trailer applications because of the low profile and they don’t require any roof perforation. If adhered to a clean metal or rubber surface and pressed down firmly with a roller, they adhere very well on sloped and curved surfaces. They are also perfect for portable solar power generators as they can be rolled up into a 16″ box and transported, and are popular as rooftop panels on RVs, campers, Quonset huts, metal standing-seam roofs, etc… due to the low profile, flexibility, and lack of wind resistance. Uni-Solar marketed these as «panels», but are really more like «solar shingles». These flexible panels have a couple of distinct advantages over rigid panels: – They don’t lose efficiency at higher temperatures as most rigid panels do. These maintain efficiency and flexibility in all temperature ranges from winter to summer. – Individual laminate layers convert red, green, and blue light into electricity to operate in the full spectrum. Even on a cloudy day, these panels will produce some electricity. Many rigid panels only work in full sun. – The 20 individual cells on each panel are wired with bypass diodes that allow each cell to function independently so that the panel can continue to produce electricity under partial shading, when dusty, or some snow. Rigid panels typically shut down completely if partially shaded. Most rigid panels on the market shut down completely if partially shaded. These continue to produce power from the cells that aren’t shaded. – Extremely durable – Rigid panels have glass that can crack or shatter when hit with hail, baseballs, etc.. The flexible laminates on these panels can’t crack or break. Multiple panels can be wired together either in series or in parallel to meet your power needs or inverter specs. Certified by Miami-Dade County in Florida to be suitable for installation in hurricane areas. Once adhered properly, they can withstand high winds, or on an RV rooftop at freeway speeds. Maximum Power (Pmax): 116 Watts Nominal Operating Voltage: 30 Volts Nominal Power Voltage (Vmpp): 24 Volts Max Power Current (Impp): 3.88 Amps Open Circuit Voltage (Voc): 43.2 Volts Short Circuit Current (Isc): 4.8 Amps Max System Voltage: 600 Volts Lightweight & Flexible Easy Peel & Stick Application Virtually Unbreakable (No Glass) Shadow & High Heat Tolerant Cells Per Module: 20 Frame Material: Frameless Module Connector: MC3 Bonding adhesive factory-installed on the back of the laminate Panel Weight: 16 Pounds Panel Dimensions:198.25″ (16.25 Feet) long, 15 3/8″ wide, .2″ thick

Uni-Solar PVL-116 116W 24V Flexible Amorphous Solar Panel w/MC3 Cables UL LISTED

Uni-Solar PVL-116 *UL LISTED* 116 Watt 24 Volt Brand New Flexible Amorphous Solar Panel with MC3 Connectors. These panels are just over 16 feet long. Electrical Stats: Maximum Power (Pmax): 116 Watts Nominal Operating Voltage: 24 Volts Peak Power (Volts): 30 Volts Peak Power (Amps): 3.88 Amps Open Circuit Volts: 43.2 Volts Short Circuit Amps: 4.8 Amps Physical Stats: Panel Dimensions (Feet): 16.4 long x 1.29 wide Panel Dimensions (Inches): 197.3 long x 15.5 wide x 0.2 thick Panel Weight: 15.5 Pounds Electrical Connectors: MC3 Connectors – Push / Pull apart Features: Lightweight & Flexible Easy Peel & Stick Application Virtually Unbreakable (No Glass) Shadow & High Heat Tolerant Frame Material: Frameless Bonding adhesive factory-installed on the back of the laminate

Uni-Solar PVL-24 5V 24W Flexible 3-Foot Solar Panel w/ Solder Points – No Cables

Uni-Solar PVL-24 5V 24W Flexible 3-Foot Solar Panel w/ Solder Points – No Cables Uni-Solar PVL-24 5V 24W Flexible Amorphous 3-Foot Long Solar Panel Battery Charger. Combine 3 of these panels in series to increase voltage for charging 12 Volt Batteries. No Cables or Junction Box Included DIY. Category 3 (130 MPH) Hurricane uplift resistant when installed in accordance with manufacturer’s guidelines. Designed for 5V USB voltage charging (No USB port Included). Combine multiple panels to increase voltage as needed for various battery configurations. Small form factor for custom Vehicle solar charging. These 36 inch long 3 cell panels are the shortest PVL Series panels Unisolar Made allowing multiple panels to be connected to fit small roof surface applications such as Golf Carts, VW Vans and Experimental Electric Vehicles. Panels are roll-able to about 6 inches in diameter to take hiking and backpacking. Previous customers have reported installing these panels on their corrugated metal roofs by attaching 18″ x 2″ metal strips every few feet on the sticky backing, leaving the white covering for the sticky backing intact where the metal strips are not present (saving the sticky material for other projects in case the panel is moved later). They then drove self-tapping screws through the protruding ends of the metal strips onto their metal roof, sealed with a proper caulk. This allowed them to install the panel with its built-in sticky backing and yet keep the installation non-permanent. Electrical Stats: Maximum Power (Pmax): 24 Watts Nominal Operating Voltage: 5 Volts (approximately) Max Power Voltage (Vmpp): 4.6 Volts Max Power Current (Impp): 5.2 Amps Open Circuit Voltage (Voc): 6.1 Volts Physical Stats: Panel Dimensions (Feet): 3 long x 1.29 wide Panel Dimensions (Inches): 36 long x 15.5 wide x 0.2 thick Panel Weight: 2.75 Pounds Electrical Connectors: None: Solder Points on top of panel Features: Lightweight & Flexible Easy Peel & Stick Application Virtually Unbreakable (No Glass) Shadow & High Heat Tolerant Frame Material: Frameless Bonding adhesive factory-installed on the back of the laminate Uni-Solar panels are lightweight, flexible and directly adhere to many roofing surfaces avoiding penetrations. Each cell is connected to each other via bypass diodes. Therefore, if one cell is shaded or soiled, only the power output of this one shaded cell is lost – usually less than 4.5%.These panels are less than 1/5th the weight of crystalline solar panels and are designed for membrane and metal roofing system applications. Here is a video with many examples.  UNISOLAR PVL-24 Solar Power Amorphous Flexible PV Panels – YouTube Video will open in a new window [isdntekvideo]   Condition: Open Box This new open box panel has top-facing solder points for connections above the panel. When 3 of these panels are combined in series they will produce a good voltage for charging 12 Volt Batteries. We are not including any cable or junction boxes but the solder points are easy to access and will allow you to attach your own cable by soldering.Please review our photo set and contact us if you have any questions.CLICK BELOW FOR MORE SOLAR OPTIONSShippingBest OffersReturns