Item Category: Electrical Supplies

VMAX V35-857 + U1 Battery Box AGM Deep Cycle 12V 35AH Battery for PV SOLAR PANEL

V35-857 + U1 Battery Box VMAX AGM Deep Cycle 12V 35AH Battery for PV SOLAR PANEL V35-857 Battery plus VBB-U1 Battery Box Nominal Voltage20Hr CapacityRC (min) CCAMCA Terminal Posts DimensionsWeight Charging Current* Charging Voltage Float Voltage 12V35AH 75 3003906mm (included) 7.7″w x 5″d x 6.1″h25lb 3A-15A 14.4-14.9V 13.5V-13.8V Recommended Charging Options: AC Chargers: Any Quality Brand AGM- Smart & Microprocessor controlled- charger with the recommended specs above can be used. Vehicle Alternator: 14V-15V.RV Converter: 14V-15V. Solar Panel: 65W-200W.Wind Turbine: 65W-200W. Charge Controller: 7A-30A.* Warning: Do not use a charger with smaller amperage than the recommended Charging Current shown above. Maintainers should ONLY be used to maintain a fully charged battery but NEVER as a charger. Operating Temperature Range: Discharge: -4~140FCharge: 14~140FStorage: -4~140F Temperature Compensation: Cycle use: -30mV/C Standby use: -20mV/C BCI Group Codes*: Matching Termination: U1 (+ on L.H.S. & – on R.H.S) * Matching is based on closest dimensional specifications. Differences in hold downs and termination may require some accommodations and/or the extension of one or both vehicle’s battery cables. Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier – USAUP TO 50% DISCOUNTSTOP BRANDSPaymentShippingReturnsPaymentShippingReturns We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement. If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. See our other itemsThank you for visiting our Ebay store!V35-857 Battery plus VBB-U1 Battery Box Nominal Voltage 20Hr Capacity RC (min) CCA MCA Terminal Posts Dimensions Weight Charging Current* Charging Voltage Float Voltage 12V 35AH 75 300 390 6mm (included) 7.7″w x 5″d x 6.1″h 25lb 3A-15A 14.4-14.9V 13.5V-13.8V Recommended Charging Options: —AC Chargers: Any Quality Brand AGM- Smart & Microprocessor controlled- charger with the recommended specs above can be used. —Vehicle Alternator: 14V-15V. —RV Converter: 14V-15V. —Solar Panel: 65W-200W. —Wind Turbine: 65W-200W. —Charge Controller: 7A-30A. * Warning: Do not use a charger with smaller amperage than the recommended Charging Current shown above. Maintainers should ONLY be used to maintain a fully charged battery but NEVER as a charger. Operating Temperature Range: —Discharge: -4~140F —Charge: 14~140F —Storage: -4~140F Temperature Compensation: —Cycle use: -30mV/C —Standby use: -20mV/C BCI Group Codes*: Matching Termination: U1 (+ on L.H.S. & – on R.H.S) * Matching is based on closest dimensional specifications. Differences in hold downs and termination may require some accommodations and/or the extension of one or both vehicle’s battery cables. V35-857 + U1 Battery Box VMAX AGM Deep Cycle 12V 35AH Battery for PV SOLAR PANEL V35-857 Battery plus VBB-U1 Battery Box Nominal Voltage20Hr CapacityRC (min) CCAMCA Terminal Posts DimensionsWeight Charging Current* Charging Voltage Float Voltage 12V35AH 75 3003906mm (included) 7.7″w x 5″d x 6.1″h25lb 3A-15A 14.4-14.9V 13.5V-13.8V Recommended Charging Options: AC Chargers: Any Quality Brand AGM- Smart & Microprocessor controlled- charger with the recommended specs above can be used. Vehicle Alternator: 14V-15V.RV Converter: 14V-15V. Solar Panel: 65W-200W.Wind Turbine: 65W-200W. Charge Controller: 7A-30A.* Warning: Do not use a charger with smaller amperage than the recommended Charging Current shown above. Maintainers should ONLY be used to maintain a fully charged battery but NEVER as a charger. Operating Temperature Range: Discharge: -4~140FCharge: 14~140FStorage: -4~140F Temperature Compensation: Cycle use: -30mV/C Standby use: -20mV/C BCI Group Codes*: Matching Termination: U1 (+ on L.H.S. & – on R.H.S) * Matching is based on closest dimensional specifications. Differences in hold downs and termination may require some accommodations and/or the extension of one or both vehicle’s battery cables. Hurricane Wind Power 2019Corporate America Today2019 Best Off-Grid Renewable Energy Product Supplier – USAUP TO 50% DISCOUNTSTOP BRANDSSee our other itemsPayment We accept payment by any of the following methods: PayPal Please pay as soon as possible after winning an auction, as that will allow us to post your item to you sooner! Shipping We offer Fast shipping on all orders! Your order will be dispatched within 1-3 working day of receiving payment (Monday-Friday) and you should expect to receive it one or two days after dispatch (for orders sent RM 1st Class). In the very unlikely event that your item is lost or damaged during post, then WE are responsible and will issue either a full refund or replacement.Returns If you are not 100% satisfied with your purchase, you can return the product and get a full refund or exchange the product for another one, be it similar or not. You can return a product for up to 14 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Thank you for visiting our Ebay store! V35-857 Battery plus VBB-U1 Battery Box Nominal Voltage20Hr CapacityRC (min) CCAMCA Terminal Posts DimensionsWeight Charging Current* Charging Voltage Float Voltage 12V35AH 75 3003906mm (included) 7.7″w x 5″d x 6.1″h25lb 3A-15A 14.4-14.9V 13.5V-13.8V Recommended Charging Options: AC Chargers: Any Quality Brand AGM- Smart & Microprocessor controlled- charger with the recommended specs above can be used. Vehicle Alternator: 14V-15V.RV Converter: 14V-15V. Solar Panel: 65W-200W.Wind Turbine: 65W-200W. Charge Controller: 7A-30A.* Warning: Do not use a charger with smaller amperage than the recommended Charging Current shown above. Maintainers should ONLY be used to maintain a fully charged battery but NEVER as a charger. Operating Temperature Range: Discharge: -4~140FCharge: 14~140FStorage: -4~140F Temperature Compensation: Cycle use: -30mV/C Standby use: -20mV/C BCI Group Codes*: Matching Termination: U1 (+ on L.H.S. & – on R.H.S) * Matching is based on closest dimensional specifications. Differences in hold downs and termination may require some accommodations and/or the extension of one or both vehicle’s battery cables.

Nanosolar 15,600 Watt Carton of 2.6W Flexible CIGS NanoCell Solar Cells 6000ct

Nanosolar 6000ct 15,600 Watt Carton of 2.6W Flexible CIGS NanoCell Solar Cells  Nanosolar NanoCell 15.6KW Lot of 6,000 2.6 Watt Lightweight Flexible Aluminum CIGS MWT Solar Cells   This listing is for a full 15,600 Watt Carton of 6,000 cells. Each individual solar cell has a maximum electrical output (mppt) of 0.45 volts at 5.8 amps which calculates to 2.6 watts each. These CIGS solar cells took over 70 steps to produce on multiple machines with hundreds of workers in a 200,000 sf factory in San Jose California.   The cells are made on thin flexible aluminum sheets which make them difficult to weld or solder even with Alumiflux solder flux paste. We have had success using double sided conductive tape to connect. You can see the video of the output 10 cells connected with the tape have produced in partial sun conditions. We find these cells even produce energy when placed under a light bulb. Manufacturers Specifications Raw Solar Cell Uncoated Rated Power: 2.6 Watts per Cell Vmpp (V) 0.45 Impp (A) 5.8 Voc (V) 0.61 Isc (A) 6.7 Operating Module Temperature -40 to +85C Length: 165mm (6.5 inches) Width: 135mm (5.3 inches) Height: 0.4mm (0.02 inches) Weight: 18.5g Per Cell Raw Solar Cell Uncoated Lightweight Aluminum Structure CIGS Solar Cells which are Semi-Flexible   Product manuals, data sheets, specifications, etc…. are available in the DOWNLOADS tab above.  Contact us if you have any questions. These raw flexible solar cells are extremely rare and have never been offered for sale to the public before. These came from the last experimental production runs at the Nanosolar Facility in California. The facility and company was liquidated during September and October of 2013. We can ship these in 2,500 Watt bin racks of 1,000 cells if you would like a smaller quantity. These raw solar cells are very robust for CIGS, however, will degrade if not encapsulated in weather tight enclosure. Its interesting for experiment we have left a few exposed and un-encapsulated for 2 years and have found minimal degradation. The CIGS solar cells are made of aluminum and to connect them we have used double sided conductive acrylic adhesive tape made by 3M / Tape Case (1182). Nanosolar used ultrasonic metal spot welders to connect the cells in production We have found a spot welder does connect them but if the settings are not just right you will blow a hole through them or the connection is weak. We believe a combination of the 3M 1182 tape and spot weld may be the best choice for DIY applications. We have had many questions regarding cutting these cells. When these cells are cut they retain their .45 volts but the amps are reduced somewhat proportionally. You cannot use regular scissors or tin snips as these are made of 2 thin sheets of aluminum separated by energy producing compounds. If the top (negative) and bottom (positive) aluminum sheets touch it shorts the cell. We have successfully cut these cells with a water-jet cutter as well as a sharp bench shear set at 45 degree angle. It is possible to cut and then sand the cut edges back until the two sheets are separated but that is a tedious task and not recommended. Also we have noticed the cut cells are not as robust as the uncut cells even when accounting for the size differences of the cells. The large area of metal (nickel coated aluminum) back is the positive output of the cell. The thin strip of un-coated aluminum on the down-facing side of the front is the negative output of the cell. Let me know if you have any questions about these cells. These came from the manufacturing floor of Nanosolar in San Jose and are being stored in air tight bags with desiccant. Each cell was tested for proper output by Nanosolar before being packaged and we have found these are very robust cells. These solar cells can be previewed at our facility in Ventura, California.   Condition: New These Aluminum Solar Cells are very Rare and the only Ones of their Kind. They are New and Unused. They are stored in air tight sealed cartons with desiccant to prolong shelf life. They are in excellent new condition. Please view our photo set and contact us if you have any questions.   CLICK BELOW FOR MORE SOLAR OPTIONSShippingBest OffersReturns

Nanosolar Lot of 1000 NanoCells 2.6KW Lightweight Flexible CIGS MWT Solar Cells

Nanosolar Lot of 1000 NanoCells 2.6KW Lightweight Flexible CIGS MWT Solar CellsNanosolar NanoCell 2,600 Watt Lot of 1,000 2.6 Watt Lightweight Flexible Aluminum CIGS MWT Solar Cells This is for a full 1,000 cell carrier. This is for a lot of 1000 solar cells that total 2,600 watts. These are rated at about 0.45 volts at 5.8 amps and are a flexible cell made on a semi rigid but flexible aluminum base. We have found 3M double sided conductive tape is the best way to connect these cells for the do it yourself method. We are also experimenting with battery tab spot welders. Nanosolar used Ultrasonic welders to assemble these into panels. Manufacturer Specifications: Raw Solar Cell Uncoated Rated Power: 2.6 Watts Vmpp (V) 0.45 Impp (A) 5.8 Voc (V) 0.61 Isc (A) 6.7 Operating Module Temperature -40 to +85C Length: 165mm (6.5 inches) Width: 135mm (5.3 inches) Height: 0.4mm (0.02 inches) Weight: 18.5g Raw Solar Cell Uncoated Lightweight Aluminum Structure CIGS Solar Cells which are Semi-Flexible MWT Metal Wrap-Through Solar Cell Technology Product manuals, data sheets, specifications, etc…. are available in the DOWNLOADS tab above.  Contact us if you have any questions. These raw flexible solar cells are extremely rare and have never been offered for sale to the public before. These came from the last experimental production runs at the Nanosolar Facility in California. The facility and company was liquidated during September and October of 2013. We can ship these in bin racks of 1,000 cells and cartons of 6,000 cells if you would like larger quantities. These raw solar cells are very robust for CIGS, however, will degrade if not encapsulated in weather tight enclosure. Its interesting for experiment we have left a few exposed and un-encapsulated for 2 years and have found minimal degradation. The CIGS solar cells are made of aluminum and to connect them we have used double sided conductive acrylic adhesive tape made by 3M / Tape Case (1182). Nanosolar used ultrasonic metal spot welders to connect the cells in production We have found a spot welder does connect them but if the settings are not just right you will blow a hole through them or the connection is weak. We believe a combination of the 3M 1182 tape and spot weld may be the best choice for DIY applications. We have had many questions regarding cutting these cells. When these cells are cut they retain their .45 volts but the amps are reduced somewhat proportionally. You cannot use regular scissors or tin snips as these are made of 2 thin sheets of aluminum separated by energy producing compounds. If the top (negative) and bottom (positive) aluminum sheets touch it shorts the cell. We have successfully cut these cells with a water-jet cutter as well as a sharp bench shear set at 45 degree angle. It is possible to cut and then sand the cut edges back until the two sheets are separated but that is a tedious task and not recommended. Also we have noticed the cut cells are not as robust as the uncut cells even when accounting for the size differences of the cells. The large area of metal (nickel coated aluminum) back is the positive output of the cell. The thin strip of un-coated aluminum on the down-facing side of the front is the negative output of the cell. Let me know if you have any questions about these cells. These came from the manufacturing floor of Nanosolar in San Jose and are being stored in air tight bags with desiccant. Each cell was tested for proper output by Nanosolar before being packaged and we have found these are very robust cells. These solar cells can be previewed at our facility in Ventura, California.   Condition: New These Aluminum Solar Cells are very Rare and the only Ones of their Kind. They are New and Unused. They are stored in air tight sealed cartons with desiccant to prolong shelf life. They are in excellent new condition. Please view our photo set and contact us if you have any questions.CLICK BELOW FOR MORE SOLAR OPTIONSShippingBest OffersReturns

Solopower 14.5″ x 1.5″ Flexible and Lightweight 1.25W CIGS Solar Cell -Lot of 10

Solopower 14.5″ x 1.5″ Flexible and Lightweight 1.25W CIGS Solar Cell -Lot of 10  Solopower 1.25 to 1.5 Watt, 14.5″ x 1.5″ Flexible and Lightweight CIGS Solar Cell – Lot of 10 These stainless steel super flexible cells came from Solopower in San Jose, California. We have been unable to locate any written specifications but we have measured them to be 0.50 volts. Regarding the amp output these are the same type of cell used in the Solopower SL1 panels which used 60 cells for 75 watt panels making them just over 1 watt per cell. The entire underside is the «positive» connection and the white bar on the sun-side is the «negative» connection. Raw Solar Cell – uncoated. Will need to be encapsulated to withstand weather. Length: 368.5mm (14.5 inches) Width: 38.1mm (1.5 inches) Height: .253mm (.01 inches) Individual Cell Weight: 0.32 oz Lightweight Stainless Steel Structure CIGS Solar Cells which are Semi-Flexible Condition: New These solar cells are new from the manufacturer. They are uncoated and Will need to be encapsulated to withstand weather.Please view our photo set and contact us if you have any questions.   CLICK BELOW FOR MORE SOLAR OPTIONSShippingBest OffersReturns